diff mbox

[dpdk-dev] Correcting upstream kernel version in driver

Message ID 1455146881-42882-1-git-send-email-john.griffin@intel.com (mailing list archive)
State Accepted, archived
Headers

Commit Message

Griffin, John Feb. 10, 2016, 11:28 p.m. UTC 
  Fixing the version of the kernel required in the QAT documentation.

Signed-off-by: John Griffin <john.griffin@intel.com>
---
 doc/guides/cryptodevs/qat.rst | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

Comments

Doherty, Declan Feb. 19, 2016, 4:43 p.m. UTC | #1 
On 10/02/16 23:28, John Griffin wrote:
> Fixing the version of the kernel required in the QAT documentation.
>
> Signed-off-by: John Griffin <john.griffin@intel.com>
> ---
>   doc/guides/cryptodevs/qat.rst | 12 ++++++------
>   1 file changed, 6 insertions(+), 6 deletions(-)
>
> diff --git a/doc/guides/cryptodevs/qat.rst b/doc/guides/cryptodevs/qat.rst
> index 1901842..23402b4 100644
> --- a/doc/guides/cryptodevs/qat.rst
>
...
>

Acked by: Declan Doherty <declan.doherty@intel.com>
Thomas Monjalon Feb. 24, 2016, 2:18 p.m. UTC | #2 
2016-02-19 16:43, Declan Doherty:
> On 10/02/16 23:28, John Griffin wrote:
> > Fixing the version of the kernel required in the QAT documentation.
> >
> > Signed-off-by: John Griffin <john.griffin@intel.com>
> 
> Acked by: Declan Doherty <declan.doherty@intel.com>

Applied, thanks
diff mbox

Patch

diff --git a/doc/guides/cryptodevs/qat.rst b/doc/guides/cryptodevs/qat.rst
index 1901842..23402b4 100644
--- a/doc/guides/cryptodevs/qat.rst
+++ b/doc/guides/cryptodevs/qat.rst
@@ -33,7 +33,7 @@  Quick Assist Crypto Poll Mode Driver
 The QAT PMD provides poll mode crypto driver support for **Intel QuickAssist
 Technology DH895xxC** hardware accelerator.
 
-The QAT PMD has been tested on Fedora 21 64-bit with gcc and on the 4.3
+The QAT PMD has been tested on Fedora 21 64-bit with gcc and on the 4.4
 kernel.org Linux kernel.
 
 
@@ -73,9 +73,9 @@  Installation
 To use the DPDK QAT PMD an SRIOV-enabled QAT kernel driver is required. The
 VF devices exposed by this driver will be used by QAT PMD.
 
-If you are running on kernel 4.3 or greater, see instructions for
+If you are running on kernel 4.4 or greater, see instructions for
 `Installation using kernel.org driver`_ below. If you are on a kernel earlier
-than 4.3, see `Installation using 01.org QAT driver`_.
+than 4.4, see `Installation using 01.org QAT driver`_.
 
 
 Installation using 01.org QAT driver
@@ -157,13 +157,13 @@  If the build or install fails due to mismatching kernel sources you may need to
 Installation using kernel.org driver
 ------------------------------------
 
-Assuming you are running on at least a 4.3 kernel, you can use the stock kernel.org QAT
+Assuming you are running on at least a 4.4 kernel, you can use the stock kernel.org QAT
 driver to start the QAT hardware.
 
 The steps below assume you are:
 
 * Running DPDK on a platform with one ``DH895xCC`` device.
-* On a kernel at least version 4.3.
+* On a kernel at least version 4.4.
 
 In BIOS ensure that SRIOV is enabled and VT-d is disabled.
 
@@ -190,7 +190,7 @@  Using the sysfs, enable the VFs::
 
     echo 32 > /sys/bus/pci/drivers/dh895xcc/0000\:03\:00.0/sriov_numvfs
 
-If you get an error, it's likely you're using a QAT kernel driver earlier than kernel 4.3.
+If you get an error, it's likely you're using a QAT kernel driver earlier than kernel 4.4.
 
 To verify that the VFs are available for use - use ``lspci -d:443`` to confirm
 the bdf of the 32 VF devices are available per ``DH895xCC`` device.