[dpdk-dev] crypto/qat: add Intel(R) QuickAssist C3xxx device
Commit Message
Signed-off-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
---
doc/guides/cryptodevs/qat.rst | 71 ++++++++++++++++++++++++++++++++--
drivers/crypto/qat/rte_qat_cryptodev.c | 3 ++
2 files changed, 71 insertions(+), 3 deletions(-)
Comments
-----Original Message-----
From: Jain, Deepak K
Sent: Friday, August 26, 2016 1:28 PM
To: Trahe, Fiona <fiona.trahe@intel.com>; Griffin, John <john.griffin@intel.com>; De Lara Guarch, Pablo <pablo.de.lara.guarch@intel.com>
Cc: dev@dpdk.org; Jain, Deepak K <deepak.k.jain@intel.com>
Subject: [PATCH] crypto/qat: add Intel(R) QuickAssist C3xxx device
Signed-off-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
Acked-by: Fiona Trahe <fiona.trahe@intel.com>
Hi Deepak,
> -----Original Message-----
> From: Jain, Deepak K
> Sent: Friday, August 26, 2016 5:28 AM
> To: Trahe, Fiona; Griffin, John; De Lara Guarch, Pablo
> Cc: dev@dpdk.org; Jain, Deepak K
> Subject: [PATCH] crypto/qat: add Intel(R) QuickAssist C3xxx device
>
> Signed-off-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
Could you send a v2 with a release notes update?
Thanks,
Pablo
HI Pablo,
> -----Original Message-----
> From: De Lara Guarch, Pablo
> Sent: Wednesday, September 7, 2016 7:08 PM
> To: Jain, Deepak K <deepak.k.jain@intel.com>; Trahe, Fiona
> <fiona.trahe@intel.com>; Griffin, John <john.griffin@intel.com>
> Cc: dev@dpdk.org
> Subject: RE: [PATCH] crypto/qat: add Intel(R) QuickAssist C3xxx device
>
> Hi Deepak,
>
> > -----Original Message-----
> > From: Jain, Deepak K
> > Sent: Friday, August 26, 2016 5:28 AM
> > To: Trahe, Fiona; Griffin, John; De Lara Guarch, Pablo
> > Cc: dev@dpdk.org; Jain, Deepak K
> > Subject: [PATCH] crypto/qat: add Intel(R) QuickAssist C3xxx device
> >
> > Signed-off-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
>
> Could you send a v2 with a release notes update?
>
Agreed. I will send v2 with release notes.
> Thanks,
> Pablo
@@ -77,6 +77,7 @@ Limitations
* Snow3g(UEA2) supported only if cipher length, cipher offset fields are byte-aligned.
* Snow3g(UIA2) supported only if hash length, hash offset fields are byte-aligned.
* No BSD support as BSD QAT kernel driver not available.
+* Snow3g (UIA2) not supported in the PMD of **Intel QuickAssist Technology C3xxx** device.
Installation
@@ -89,13 +90,15 @@ If you are running on kernel 4.4 or greater, see instructions for
`Installation using kernel.org driver`_ below. If you are on a kernel earlier
than 4.4, see `Installation using 01.org QAT driver`_.
-For **Intel QuickAssist Technology C62x** device, kernel 4.5 or greater is
+For **Intel QuickAssist Technology C62x** and **Intel QuickAssist Technology C3xxx**
+device, kernel 4.5 or greater is
needed. See instructions for `instructions using kernel.org driver`_ below.
Installation using 01.org QAT driver
------------------------------------
-NOTE: There is no driver available for **Intel QuickAssist Technology C62x** on 01.org.
+NOTE: There is no driver available for **Intel QuickAssist Technology C62x** and
+**Intel QuickAssist Technology C3xxx** devices on 01.org.
Download the latest QuickAssist Technology Driver from `01.org
<https://01.org/packet-processing/intel%C2%AE-quickassist-technology-drivers-and-patches>`_
@@ -265,7 +268,7 @@ You should see output similar to::
3d:00.0 Co-processor: Intel Corporation Device 37c8
3f:00.0 Co-processor: Intel Corporation Device 37c8
-For each c62x device there are 3 PFs.
+For each c62x device there are 3 PFs.
Using the sysfs, for each PF, enable the 16 VFs::
echo 16 > /sys/bus/pci/drivers/c6xx/0000\:1a\:00.0/sriov_numvfs
@@ -276,6 +279,48 @@ To verify that the VFs are available for use - use ``lspci -d:37c9`` to confirm
the bdf of the 48 VF devices are available per ``C62x`` device.
To complete the installation - follow instructions in `Binding the available VFs to the DPDK UIO driver`_.
+
+For **Intel QuickAssist Technology C3xxx**:
+Assuming you are running on at least a 4.5 kernel, you can use the stock kernel.org QAT
+driver to start the QAT hardware.
+
+The steps below assume you are:
+
+* Running DPDK on a platform with one ``C3xxx`` device.
+* On a kernel at least version 4.5.
+
+In BIOS ensure that SRIOV is enabled and VT-d is disabled.
+
+Ensure the QAT driver is loaded on your system, by executing::
+
+ lsmod | grep qat
+
+You should see the following output::
+
+ qat_c3xxx 16384 0
+ intel_qat 122880 1 qat_c3xxx
+
+Next, you need to expose the Virtual Functions (VFs) using the sysfs file system.
+
+First find the bdf of the physical function (PF) of the C3xxx device
+
+ lspci -d:19e2
+
+You should see output similar to::
+
+ 01:00.0 Co-processor: Intel Corporation Device 19e2
+
+For c3xxx device there is 1 PFs.
+Using the sysfs, enable the 16 VFs::
+
+ echo 16 > /sys/bus/pci/drivers/c3xxx/0000\:01\:00.0/sriov_numvfs
+
+If you get an error, it's likely you're using a QAT kernel driver earlier than kernel 4.5.
+
+To verify that the VFs are available for use - use ``lspci -d:19e3`` to confirm
+the bdf of the 16 VF devices are available per ``C3xxx`` device.
+To complete the installation - follow instructions in `Binding the available VFs to the DPDK UIO driver`_.
+
Binding the available VFs to the DPDK UIO driver
------------------------------------------------
@@ -321,3 +366,23 @@ if yours are different adjust the unbind command below::
echo "8086 37c9" > /sys/bus/pci/drivers/igb_uio/new_id
You can use ``lspci -vvd:37c9`` to confirm that all devices are now in use by igb_uio kernel driver.
+
+For **Intel(R) QuickAssist Technology C3xxx** device:
+The unbind command below assumes ``bdfs`` of ``01:01.00-01:02.07``,
+if yours are different adjust the unbind command below::
+
+ cd $RTE_SDK
+ modprobe uio
+ insmod ./build/kmod/igb_uio.ko
+
+ for device in $(seq 1 2); do \
+ for fn in $(seq 0 7); do \
+ echo -n 0000:01:0${device}.${fn} > \
+ /sys/bus/pci/devices/0000\:01\:0${device}.${fn}/driver/unbind; \
+
+ done; \
+ done
+
+ echo "8086 19e3" > /sys/bus/pci/drivers/igb_uio/new_id
+
+You can use ``lspci -vvd:19e3`` to confirm that all devices are now in use by igb_uio kernel driver.
@@ -74,6 +74,9 @@ static struct rte_pci_id pci_id_qat_map[] = {
{
RTE_PCI_DEVICE(0x8086, 0x37c9),
},
+ {
+ RTE_PCI_DEVICE(0x8086, 0x19e3),
+ },
{.device_id = 0},
};